Linksys Cisco E1200 Version 2 DD-WRT Supported
- Dd Wrt Linksys E1200 V2
- How To Install Dd Wrt On Linksys E1200 V2 Reviews
- Dd-wrt Linksys E1200 V2
Flash the initial flash firmware: dd-wrt.v24-19519NEWD-2K2.6mini-e1200v2.bin Wait 2 minutes for the router to flash and reboot itself. Wait about another 2 minutes until it finishes booting. Log into the dd-wrt web interface and set a password Flash the Upgrade build and then reset using the GUI. Posted: Wed Apr 04, 2012 5:14 Post subject: Linksys Cisco E1200 Version 2 DD-WRT Supported Edit: This device is now ported and CFE/NVRAM dump is no longer needed DD-WRT supported at 18946.
| DD-WRT Forum Forum Index ->Broadcom SoC based Hardware |
- In this video I talk about how I can install DD-WRT Firmware on my wireless router, then I install it on my Linksys E900 Wireless Router. 3:58SUPPORT ME ON.
- Download the stock firmware image from the manufacturer's website, reset the router back to defaults using a 30-30-30 hard reset, then flash the stock image from within the dd-wrt webgui. After 5 minutes it should finish, you will then need to do another 30-30-30 reset.
- Since I had a spare Linksys E1200, I decided to do some research into DD-WRT and use the router as a wireless bridge. I followed this guide to set it up, meaning I installed this version of the DD-WRT firmware: dd-wrt.v24-18946NEWD-2K2.6mini-e1200v2.bin.
Goto page Previous1, 2, 3 ... 14, 15, 16 ... 18, 19, 20Next |
| Author | Message |
|---|
mrjcd
DD-WRT Guru
Joined: 31 Jan 2015
Posts: 5370
Location: Texas
| | Posted: Wed Apr 08, 2015 5:28 Post subject: | Hey cliper,
The wireless issues with the E1200v2 are very real and even make dd-wrt unusable on this router for certain things. Since you brought this up I'll tell you what I know without going into any techy details. Certain wireless protocol will completely confuse this router. I have seen the same issues on the E2500 and the WNDR3700v3 but was very rare and only in a couple dd-wrt builds and no I don't remember which.
I have not found a dd-wrt build, including the 18946 for the E1200v2 suitable for me to use as my main router.
Example: Using E1200v2 as router / WAP or whatever...
FTP download will be at 1 mbps at best. Upload not affected and is always scary fast.
Tried different FTP cleints on android phone, Galaxy S3 tab, laptops. Filezilla won't even work and it does a good job on most anything.
The dd-wrt / E1200v2 / wireless negotiation / has a big fat bug in it.
The http protocol is not too bad for me ... can download same files using browser without a problem.
Wired clients are not affected.
I still have a couple E1200v2 here that I play with and have installed many many dd-wrt builds with all the same results when it comes to that particular example.
EDIT: The example above is dealing with a secure ftp server ( ftps )
I have never tried any KONG builds .. they may solve this ????
To answer your question from http://www.dd-wrt.com/phpBB2/viewtopic.php?p=959843#959843
I am really partial to DD-WRT cause they have so many neat builds to play with but since you ask I'll be honest and say the best firmware I have found for the E1200v2 is Tomato-Shibby. It does not have this bug. I've also setup a site to site openVPN TAP using it with two E1200v2 and have never had any problems.
tomato-E1200v2-NVRAM64K-1.28.RT-N5x-MIPSR2-124-Max.bin
This is the newest. I haven't used it but I suspect it is good -
tomato-E1200v2-NVRAM64K-1.28.RT-N5x-MIPSR2-128-Max.bin
They can be found here >>> http://tomato.groov.pl/download/K26RT-N/build5x-128-EN/Linksys%20E-series/
'bout all i know
EDIT :
I've been running [dd-wrt.v24-27506_NEWD-2_K3.x_mega-nv64k.bin] (07/09/15)
on the E1200v2 as main router last few days without any problems mentioned above.
The K3.x builds seem to work very well on this router.
Last edited by mrjcd on Tue Aug 04, 2015 21:21; edited 2 times in total |
|
Sponsor
<=' td='> |
termin
DD-WRT Novice
Joined: 23 Dec 2013
Posts: 5
| | Posted: Tue Apr 14, 2015 6:22 Post subject: | So i have problem to able to work with N-speed
All connected devices speed is only 54 i try G NG and N
With only N selected can't connect via WI-FI
I try all options and cannot get speed above 54G
Im tested:
dd-wrt.v24-18946_NEWD-2_K2.6_mini-e1200v2.bin
dd-wrt.v24-21676_NEWD-2_K2.6_mini-e1200v2.bin
dd-wrt.v24-21061_NEWD-2_K2.6_mini-nv64k
dd-wrt.v24-26635_NEWD-2_K3.x_mega-e1200v2
Is here version whih can get N-speed ?
Or please fix this. |
|
Foxxe Wilder
DD-WRT Novice
Joined: 23 Jan 2014
Posts: 5
Location: Canada
| | Posted: Thu Apr 16, 2015 17:49 Post subject: Linksys e1200 v2 flash failures | I have been trying to flash my Linksys E1200-RM v2.0 but all attempts to flash to DD-WRT failed.
I don't know why it's not accepting it, I've even tried the 30-30-30 method to get to telnet but telnet fails to allow connection.
(after any flashing attempt it returns to an unsecured yet usable original linksys flash)
Is there an alternate method to flashing this with as little dangers as possible?
I have used DD-WRT on my old WRT54gl for years with no problems at all. (I only set it aside as internet download speeds became faster than it could handle.) |
|
CapinWinky
DD-WRT Novice
Joined: 20 Apr 2015
Posts: 2
| | Posted: Mon Apr 20, 2015 14:54 Post subject: | I'm trying to get some kind of client mode working to provide internet to a wired device via a phone hotspot. Apparently Tomato has issues with client mode if the primary isn't also a Tomato router and I'm hoping DD-WRT does not have this issue.
I am a little surprised to hear there are problems with N wireless speeds, but I ultimately don't care that much. I'm going to just go with the 21676 NEWD mini and will report if it worked.
EDIT: To clarify, I already tried Shibby Tomato 124 and 128 and it did not work in client or bridge mode, even when connecting to a router instead of phone hotspot.
EDIT2: I tried with the named mini for the E1200v2 and client mode worked right away. It did have issues with the my work wifi, but that seems to be an issue with fortinet blocking it and no fault of dd-wrt.
Last edited by CapinWinky on Mon Apr 20, 2015 16:09; edited 1 time in total |
|
CapinWinky
DD-WRT Novice
Joined: 20 Apr 2015
Posts: 2
| | Posted: Mon Apr 20, 2015 15:24 Post subject: | Not sure why no one pointed this out, but there is a fix for the slow download speeds on N.
In Administration -> Commands put:
Click Save Startup.
Then Enter:
| Code: | | iptables -t mangle -A PREROUTING -i `nvram get wan_ifname` -j DSCP --set-dscp 0 |
Click Save Firewall
This works because Comcast and some others encode the IPv4 packets with DSCP value of 8 instead of 0 and a bug in the WMM driver mishandles them. The script converts the DSCP value to 0 when the packet arrives at the WAN port, avoiding the issue.
http://www.dd-wrt.ca/wiki/index.php/Comcast_download_speed_fix_for_Linksys_eSeries |
|
cliper
DD-WRT Novice
Joined: 06 Apr 2015
Posts: 6
| | Posted: Mon Apr 20, 2015 17:12 Post subject: | | CapinWinky wrote: | Not sure why no one pointed this out, but there is a fix for the slow download speeds on N.
In Administration -> Commands put:
Click Save Startup.
Then Enter:
| Code: | | iptables -t mangle -A PREROUTING -i `nvram get wan_ifname` -j DSCP --set-dscp 0 |
Click Save Firewall
This works because Comcast and some others encode the IPv4 packets with DSCP value of 8 instead of 0 and a bug in the WMM driver mishandles them. The script converts the DSCP value to 0 when the packet arrives at the WAN port, avoiding the issue.
http://www.dd-wrt.ca/wiki/index.php/Comcast_download_speed_fix_for_Linksys_eSeries |
well, it's not certainly an issue with dscp.. I think that's pointed to a Comcast ISP issue.
_________________
Linksys E1200 v2
DD-WRT v24-sp2 (05/27/13) mini - build 21676 (reverted to stock april 7, 2015 wifi issues) |
|
RedRover
DD-WRT Novice
Joined: 27 Apr 2014
Posts: 16
| | Posted: Sun May 10, 2015 22:41 Post subject: | | mrjcd wrote: | Hey cliper,
The wireless issues with the E1200v2 are very real and even make dd-wrt unusable on this router for certain things. Since you brought this up I'll tell you what I know without going into any techy details. Certain wireless protocol will completely confuse this router. I have seen the same issues on the E2500 and the WNDR3700v3 but was very rare and only in a couple dd-wrt builds and no I don't remember which.
I have not found a dd-wrt build, including the 18946 for the E1200v2 suitable for me to use as my main router.
Example: Using E1200v2 as router / WAP or whatever...
FTP download will be at 1 mbps at best. Upload not affected and is always scary fast.
Tried different FTP cleints on android phone, Galaxy S3 tab, laptops. Filezilla won't even work and it does a good job on most anything.
The dd-wrt / E1200v2 / wireless negotiation / has a big fat bug in it.
The http protocol is not too bad for me ... can download same files using browser without a problem.
Wired clients are not affected.
I still have a couple E1200v2 here that I play with and have installed many many dd-wrt builds with all the same results when it comes to that particular example.
EDIT: The example above is dealing with a secure ftp server ( ftps )
I have never tried any KONG builds .. they may solve this ????
To answer your question from http://www.dd-wrt.com/phpBB2/viewtopic.php?p=959843#959843
I am really partial to DD-WRT cause they have so many neat builds to play with but since you ask I'll be honest and say the best firmware I have found for the E1200v2 is Tomato-Shibby. It does not have this bug. I've also setup a site to site openVPN TAP using it with two E1200v2 and have never had any problems.
tomato-E1200v2-NVRAM64K-1.28.RT-N5x-MIPSR2-124-Max.bin
This is the newest. I haven't used it but I suspect it is good -
tomato-E1200v2-NVRAM64K-1.28.RT-N5x-MIPSR2-128-Max.bin
They can be found here >>> http://tomato.groov.pl/download/K26RT-N/build5x-128-EN/Linksys%20E-series/
'bout all i know |
Let me confirm, Tomato by Shibby is the BEST THING that has happened to the e1200. It is way faster than stock 2.0.0.6 (I noticed 2.0.0.7 has been published in January). Stock by the way was faster than DD-WRT for me. Tomato seems to be running rock solid. I flashed from DD-WRT no problem. Works great with Surface by Microsoft in terms of mbps. Downloads are above 67mbps and latancy below 17ms for Charter 60mbps service. Stable! And more features for my liking than DD-WRT, including dynamicDNS for OpenDNS, DNSmasq features, and more. Thanks!!! (Running 128)
_________________
WRT-54G V6 & V8 - wrt.v24_micro_generic.bin
Linksys E1200 v2 - Tomato by Shabby (DD-WRT has problems)
EA6300 V1 - Kong+CFE http://www.desipro.de/ddwrt/K3-AC-Arm/dd-wrt.v24-K3_AC_ARM_STD.bin |
|
Nonaem
DD-WRT Novice
Joined: 03 Jun 2015
Posts: 5
| | Posted: Wed Jun 03, 2015 10:29 Post subject: | Hi all!
Can't flash my E1200 v2.
Current firmware: stock
2.3.00 build 1 Окт(October) 14, 2013
1fba85f8f7b256a826ae2bd4d807a5a3
I'm doing all like it described here:
http://dd-wrt.com/wiki/index.php/Linksys_E1200v2
http://www.dd-wrt.com/wiki/index.php/Installation
bin from wiki page:
ftp://ftp.dd-wrt.com/betas/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_mini-e1200v2.bin
'Update error' at 4-6%.
Tested this file instead of previous (must be the second, i know) - same shit.
ftp://ftp.dd-wrt.com/betas/2013/05-27-2013-r21676/broadcom_K26/dd-wrt.v24-21676_NEWD-2_K2.6_mini-nv64k.bin
What's wrong?
Many thx. |
|
mrjcd
DD-WRT Guru
Joined: 31 Jan 2015
Posts: 5370
Location: Texas
| | Posted: Wed Jun 03, 2015 12:11 Post subject: | | Nonaem wrote: | Can't flash my E1200 v2.
Current firmware: stock
2.3.00 build 1 Окт(October) 14, 2013
1fba85f8f7b256a826ae2bd4d807a5a3 |
Make sure you have the E1200 version 2
E1200 v2 is much different than E1200 or E1200 v1
Download this >>> http://www.dd-wrt.com/phpBB2/viewtopic.php?p=969027#969027
Reset your router.
Power cycle the router.
Install latest Linksys firmware you downloaded.
Then follow the wiki to install dd-wrt.
Give it plenty of time (5 - 7 minutes) installing firmware.
If not not working use different web browser to update firmware. |
|
Nonaem
DD-WRT Novice
Joined: 03 Jun 2015
Posts: 5
| | Posted: Wed Jun 03, 2015 13:11 Post subject: | | mrjcd wrote: |
Make sure you have the E1200 version 2
E1200 v2 is much different than E1200 or E1200 v1
|
>Install latest Linksys firmware you downloaded.
Can't flash even it. Same error.
Here is parallel router ping. Language is not English, but it's not the problem i suppose.
Looks like link is breaking in flashing process.
| Code: | C:UsersDOrlov>ping 192.168.1.1 -n 40
Обмен пакетами с 192.168.1.1 по с 32 байтами данных:
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Общий сбой.
Общий сбой.
Ответ от 192.168.1.1: число байт=32 время=121мс TTL=100
Ответ от 192.168.1.1: число байт=32 время=1мс TTL=100
Ответ от 192.168.1.1: число байт=32 время=1мс TTL=100
Превышен интервал ожидания для запроса.
Ответ от 192.168.1.2: Заданный узел недоступен.
Ответ от 192.168.1.2: Заданный узел недоступен.
Ответ от 192.168.1.2: Заданный узел недоступен.
Превышен интервал ожидания для запроса.
Ответ от 192.168.1.1: число байт=32 время=984мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время=8мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Ответ от 192.168.1.1: число байт=32 время<1мс TTL=64
Статистика Ping для 192.168.1.1:
Пакетов: отправлено = 40, получено = 36, потеряно = 4
(10% потерь)
Приблизительное время приема-передачи в мс:
Минимальное = 0мсек, Максимальное = 984 мсек, Среднее = 33 мсек |
|
|
mrjcd
DD-WRT Guru
Joined: 31 Jan 2015
Posts: 5370
Location: Texas
| | Posted: Wed Jun 03, 2015 13:30 Post subject: | | Nonaem wrote: | Looks like link is breaking in flashing process.
|
I would hold pin reset (on bottom) for at least 20 seconds or until all lights flash. Wait 30 seconds.
Power cycle router... give it a minute to bootup good and repeat the reset and power cycle. |
|
Nonaem
DD-WRT Novice
Joined: 03 Jun 2015
Posts: 5
| | Posted: Wed Jun 03, 2015 13:58 Post subject: | I've tryed 30-30-30 reset 5 times.
Flashing latest linksys firmware stops at 8%.
DD-WRT - at 6%.
Should i try TFTP flash, like it described here?
http://www.dd-wrt.com/wiki/index.php/Tftp_flash |
|
mrjcd
DD-WRT Guru
Joined: 31 Jan 2015
Posts: 5370
Location: Texas
| | Posted: Wed Jun 03, 2015 14:15 Post subject: | | Nonaem wrote: | I've tryed 30-30-30 reset 5 times.
Flashing latest linksys firmware stops at 8%.
DD-WRT - at 6%.
Should i try TFTP flash, like it described here?
http://www.dd-wrt.com/wiki/index.php/Tftp_flash |
Yes I would try TFTP.
Best to set your computer to static IP
You will have to put in password admin in the TFTP app and either do the latest Linksys firmware or you can go straight to dd-wrt.
I always use dd-wrt.v24-21061_NEWD-2_K2.6_mini-e1200v2.bin when I've done this.
If TFTP is successful give it a few minutes until lights are steady -- don't even try to access it from http until complete these steps --- then do a pin reset (20 seconds) wait till lights are steady then unplug, wait 10 seconds plug back in.
Set computer back to DHCP
It should give you DHCP IP after 1 minute ... its slow booting dd-wrt.
If it is briefly dropping port function as your pings indicate hopefully the TFTP app will continue with the install
---- or you may have a brick --- do this at your own risk |
|
Nonaem
DD-WRT Novice
Joined: 03 Jun 2015
Posts: 5
| | Posted: Wed Jun 03, 2015 14:36 Post subject: | tftp2.exe - Fail
'unable to ger response from the server' message
Thank you for your help, I'll continue my tryes tomorrow and post results here. |
|
| DD-WRT Forum Forum Index ->Broadcom SoC based Hardware | All times are GMT |
| You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You can attach files in this forum
You can download files in this forum
|
Router setup wizard from Astrill application
Quick and Intuitive way to install Astrill vpn on Router.
It is mandatory to have a router which is flashed with DD-WRT or Tomato firmware and then you can use this Router Setup Wizard to install Astrill applet onto your router.
Step 1
Click on HELP tab from Astrill applicatio and select Router Setup... option to open Router Setup Wizard.
Step 2
Select Install Astrill on my router', check Find my router automatically and click on Next button.
You will prompted that installation is successful.
Here's how Astrill VPN applet on DD-WRT firmware router looks like:
Here's how Astrill VPN applet on Tomato firmware router looks like:
You need a router with supported firmware:
DD-WRT: v24 Build 13309 or newer.
Supported builds: OpenVPN, Big, Mega, Giga.
Tomato: v1.28 or newer.
Supported build: VPN.
You can click here to view list of supported routers
Note: Router MUST have 8 MB FLASH MEMORY for OpenVPN to be installed.
Note2: We even provide pre-installed routers with Astrill VPN at very affordable rates. All Astrill VPN routers come preinstalled with Astrill VPN and ready to use immediately. You get access to all Astrill VPN servers (115 servers in 48 countries with free and unlimited switches), and you have option to add private IPs as well. You can order them from this page - https://www.astrill.com/astrill-vpn-routers
Web install from Astrill Members Area
Web install from DD-WRT
It is possible to install Astrill OpenVPN applet on DD-WRT compatible routers without using Astrill application. Please note that requirements are the same, minimal build is 13309 (v24 or newer; Mega, Big, VPN, OpenVPN builds).
To install Astrill OpenVPN applet on your router, first navigate to the router web control panel using your browser, e.g. it could be located on http://192.168.1.1. Click on tab Administration->Commands. If you are prompted for a password, the default is root/admin (unless you have changed it). You will see a screen similar to this one:
In the Commands box type:
Please replace YOUR_EMAIL and YOUR_PASSWORD with appropriate values and make sure you don’t remove backtick (`). It’s not an apostrophe (‘).
Then hit “Run Commands” and wait a few moments. If everything went correctly, you will see the following screen:
If you have any error on this step, please double check your firmware version, make sure it has OpenVPN 2.0+ The best is to contact our support and we can schedule a remote desktop session.
Astrill is now installed on tab Status->My Page, so let’s go there. You will see the following screen:
Choose a server from the drop down box and hit Connect. We will be soon adding more servers to Astrill DD-WRT.
Dd Wrt Linksys E1200 V2
If you run into any problems, make sure you tried the following:
Command-line setup methods
It is also possible to install Astrill applet on DD-WRT flashed routers using command line as well. You can check the following articles for reference.
Windows via telnet
For Windows, you might need to enable the Telnet(Windows built-in Client):
1. To Telnet into Router, kindly open Command Prompt and enter the following command 'Telnet Your Router's IP address', for e.g. 'telnet 192.168.4.1'
2. Once you will be able to see the login option, kindly input the login credentials
The username that should be used is 'root'.
Please note that while inputting the password, you will not be able to see any asterisks/stars or any characters. Hence, after entering the password simply press 'Enter' key.
3. After successful login, you will see that the command line path will change to root.
4. Then copy the command provided by the Members Page > TOOLS > Router Set-up, as mentioned in the screenshot below:
5. Then input the correct IP Address of router and click on 'Install'
6. You will then be navigated to Router's Command Shell window. Just copy the command and paste it within Telnet window.
7. After successful installation of Astrill applet, you will be able to see the confirmation message(as mentioned within the screenshot below)
Windows via putty
TEXTGOESHERE
Mac OS X via terminal
How To Install Dd Wrt On Linksys E1200 V2 Reviews
TEXTGOESHERE
Dd-wrt Linksys E1200 V2
Retrieved from 'https://wiki.astrill.com/index.php?title=Astrill_Setup_Manual:Installing_Astrill_VPN_applet_onto_your_DD-WRT_flashed_routers&oldid=4819'